Making a vaporizer is not only easy, but you will also save your money. With just a few tools, you can make your own vaporizer in just a few minutes.
Steps
Method 1 of 3: Bulb Vaporizer
Step 1. Prepare everything you need
To make this vaporizer you will need a light bulb (a 100 watt light bulb works best), a sharp knife, pliers, glass tubes, duct tape, scissors, and a half liter bottle cap.
Step 2. Cut off the end of the bulb
Take a sharp knife and cut off the metal tip of the bulb with which you insert it into the socket. Try to cut straight to avoid rough edges.
Step 3. Remove the filament
Use pliers to remove the filament from the bulb. A filament is a metal wire that lights up a light bulb when you turn on the light. When you take it out, you are left with only an empty flask.
Step 4. Insert the cap into the end of the light bulb
Insert the bottle cap into the end of the light bulb. If the cap is too big, take some tape and slide it into the cap to create some sort of padding and the cap could fit perfectly on the edge of the light bulb.
Step 5. Make two holes in the cap
You will insert two glass tubes into these holes, so make two the correct size holes. Take a knife and cut out these two holes. If you have a drill, you can also quickly drill these two holes.
Step 6. Assemble the evaporator
Insert glass straws / tubes into the cap, and insert the bottle cap into the light bulb instead of the metal part. When you are sure everything fits, you can remove the cap and add the desired substance to the inside of the flask. Place the base of the flask over the flame to create steam that can be inhaled through the glass tubes.
Method 2 of 3: Glass Vial Vaporizer
Step 1. Take everything you need
You will need to take / buy a small glass bottle (the size of a bottle of ginseng extract, which can be bought at a pharmacy, is suitable), a small straw or tube, a sharp knife and duct tape.
Step 2. Clean the bottle
Remove everything inside the bottle and rinse it thoroughly to keep it completely clean. Do the same with the plastic bottle cap.
Step 3. Make a hole in the cap
Take your knife and cut out a round hole large enough to fit the tube through. Try to make a straight hole without rough edges.
Step 4. Insert the tube into the cap
The hole should be large enough to fit a tube into. Make a small hole at the base of the tube near the top of the cap to allow air flow.
Step 5. Assemble the evaporator
Insert the cap into the bottle and make sure all parts fit. After that, you can remove the cap to pour the desired substance into the bottle. Insert the tube into the bottle only halfway so that it does not melt from the heat and does not suck anything inside.
Method 3 of 3: Vaporizer from a shot glass
Step 1. Take everything you need
You will need a glass of thin glass, a half-liter bottle, a straw or tube, duct tape, and a sharp knife.
Step 2. Cut off the top of the bottle
Take an empty bottle and cut off the top where the cap is. Cut about 2.5 cm below the cap so that a little plastic bottle is attached to it.
Step 3. Make a hole in the cap
Unscrew the lid, take a sharp knife and make two holes so that you can insert straws or straws through them. Try to keep the edges as straight as possible.
Step 4. Insert the straws into the lid
Take two straws and slide them through the two holes you made in the lid. Don't stick them too deep. When you put the lid on the glass, the straws should be about halfway down the glass.
Step 5. Place the lid on the glass
The plastic part should be wide enough to cover the glass, but also wide enough to stick to the glass with duct tape. Pour any substance into the glass before attaching the plastic cap to the glass. Place the glass on a small flame.
Advice
- Application: pour the substance into the evaporator, and put the evaporator itself on the flame for a while at a height of about 1 cm until you see how the evaporator is filled with steam. Inhale the steam through the tubes.
- If the cap is too small, you will need to find a larger cap. If it's too large, use duct tape, glue, or some other adhesive to make some kind of upholstery in the lid.