It is not necessary to replace your old ceiling fan during renovation. If you want it to stand out less against the background of the ceiling to visually increase the space, play with new and fresh colors, or just stop looking like greetings from the 1970s, then by getting your fingers dirty a little, spending a minimum of money and time, you can repaint the fan and give it a look new product.
Steps
Part 1 of 3: Disassembling and Preparing the Fan
Step 1. If your ceiling fan has a light, then start disassembling from it
First remove the shades by unscrewing the thumbscrews holding them. Next, remove the lighting fixture by unscrewing the mounting screws. Place them back in the holes, but do not tighten completely.
A screwdriver can be done faster, but a regular Phillips screwdriver will work as well
Step 2. Remove all blades and bracket from the motor housing
Most likely, they are filming all together. Set the blades and mounting screws aside.
It's best to put all the screws in a small vase so you don't get lost inadvertently. Set it aside so as not to accidentally hit or turn it over during operation
Step 3. Remove the screws holding the fan base
Lower it carefully and disconnect the wires. At this point, you can remove the fan from the ceiling. It is better to leave the mounting bracket on the ceiling.
Step 4. On the floor, proceed to disassemble the fan housing
As the parts are disassembled, it is best to put them next to you, having previously spread newspapers, tarpaulin or any other material that you do not mind staining with paint. Disassembly is carried out in the following order:
- First, remove the blades from the bracket. Thread the screws back into the holes, but do not fully tighten.
- Next, remove the rod from the motor housing. Thread the screws into the holes on the top of the motor housing.
- Then remove the bottom panel of the motor housing. Place the bolts and screws aside.
- At the end, the chains should be removed. They can also be set aside.
Step 5. Cleaning the fan
Use a multi-purpose cleaning fluid and a damp cloth to clean the fan. You don't want to paint on dust, dead insects, and old dirt, do you? Run a good rag over the blades, engine casing, boom and other elements that you will be painting (of course, it is better to wipe even those elements that are not intended for painting).
After cleaning, let the parts dry or wipe dry with a clean cloth
Part 2 of 3: Painting the ceiling fan
Step 1. Sand the blades with 120 grit sandpaper
This will remove any residual dirt, dust or old, peeling paint. This step is not necessary if your fan is in good condition, but it is best to sand the older units with sandpaper.
Remove dust after sanding. To do this, use a clean cloth and soapy water. Let all parts dry
Step 2. Cover all elements with white primer
After putting on an old T-shirt and seals, shake the can and spray paint on an old newspaper or piece of cardboard to test. If everything is ready, then coat the blades and / or other parts with an even thin layer. Let them dry.
When painting a ceiling fan, it is best to work with a spray paint primer. A universal liquid primer can be used, but the former is easier to work with and more evenly applied
Step 3. After the white primer has dried, paint all the fan elements
Again, it is easiest (but not necessary) to use spray paint of any color and apply it from a distance of 15-20 cm. Smoothly move the can left and right to apply an even coat of paint. The best place to start is with the paddles to dry while you paint other parts.
- Neutral colors (gray, white, brown) will always be in place, but bright colors can better match the interior of the room and add mood. You can also buy paint to match the color of different metals (like nickel or copper) to make your fan look stylish and modern.
- If you do not want to paint some parts of the parts, then cover them with tape.
Step 4. After the first coat of paint has dried, cover the parts with a second coat
Wait until they dry, and then carefully examine the work done: perhaps some areas need to be tinted.
If you need to touch up a tiny dot, you can always use a marker of the desired shade
Part 3 of 3: Assembling the ceiling fan
Step 1. It's time to assemble the fan
Start with the rod, securing it with screws (is it really good that you folded them into a vase and set them aside?). Slide the base towards the motor housing. Then reinstall the bottom panel and secure the blades to the brackets.
Step 2. Hang the ceiling fan onto the mounting bracket
Then reconnect all wires using electrical tape and connectors. Move the base towards the ceiling and secure it.
If you have problems with assembly, wikiHow has articles on installing and replacing ceiling fans to help you understand the intricacies of proper installation
Step 3. Attach the blades and bracket to the motor housing
All screws must be securely tightened and positioned correctly - this is perhaps the most monotonous and boring job. There is nothing complicated about it, it just takes time.
Step 4. If your fan is equipped with a light and switch chains, then reinstall them
Once installed, pull on the chain to turn on the light. If everything works fine. If not, then you need to check the implementation of the steps described above. Something may have been executed in the wrong sequence.
Now you can sit back and enjoy the painted fan
Advice
- Always follow local electrical codes.
- When reinstalling, check that all components are securely fastened.
- Always use electrical tape and connectors to connect the wires.